"Setup did not find any hard disk drives installed in your computer" Welcome to Microsoft's Windows XP Professional "Setup cannot find hard drive" repair install guide for earlier versions released without a pre-installed service pack or service pack1. This guide is step by step and should be used when serious problems arrive within Windows that result in a no boot or the inability to login occur.
This will give you an idea on how to do this when and if the time arises for you to either reinstall the operating system, install for the first time or upgrade your present operating system. This install guide is fully graphical and will take you through each step of the installation. The error you will usually get is pictured below, but remember windows will pick up card readers, and other hard drives also. This process should only be used to access Windows for data recovery and backup, it could be possible that your issues are caused by viruses, spyware, malware, Trojans or even faulty hardware. A fresh clean install is always recommended.
| Special Notes: This version of Windows XP Professional does not support large hard drives, and if you are using one that is bigger than 137 GB then you will not be able to access any of the space above that number during install. You could consider slipstreaming the service pack onto your disk. See here Parallel installs for different operating systems are not advised fo the same partition or drive, use a separated partition of hard drive for running multiple operating systems as common files in Program Files, C: drive, user directories can clash and cause multiple errors and issues.
|
The first thing you will have to do is find out the manufacturer of your motherboard, and also the type of drive you are using. SATA (Serial ATA) Hard Drive
SATA Connectors on hard drive | SATA data cable | | |
IDE Cable
IDE (PATA) Connectors on Hard Drive | IDE (PATA) data cable | | |
Once you have determined the type of hard drive you have go to the motherboard/computer manufacturers website and download the SATA or PATA drivers for that board. Make sure if the files are compressed that you extract them to your floppy disks. Now copy the extracted files, (Or downloaded file) onto a blank floppy disk. If you are using a raid array then you will also need the motherboards raid driver.
Your Windows XP Professional CD Windows XP COA, or serial number. Your computer Plugged into Mains Power A Computer, with the usual accessories (Mouse, monitor, keyboard etc) CD-ROM/DVD Drive.
To start this Windows install. First check that the first boot device in your system BIOS is set to the CD-ROM Drive. ( To find out how to access the BIOS please refer to your motherboard manual or the manufacturer of your Computer. (The system bios can usually be entered on boot, usually by pressing the F1, F2, F8, F10 or DEL key. Make sure you save the settings before exiting)) If you are unsure or don't want to enter the BIOS then just test the computer by putting the CD-ROM in the drive and reboot your computer. This is the recommended way to install windows.
Your Windows XP Professional CD Windows XP COA, or serial number. Your computer Plugged into Mains Power A Computer, with the usual accessories (Mouse, monitor, keyboard etc) CD-ROM/DVD Drive.
To start this Windows install. First check that the first boot device in your system BIOS is set to the CD-ROM Drive. ( To find out how to access the BIOS please refer to your motherboard manual or the manufacturer of your Computer. (The system bios can usually be entered on boot, usually by pressing the F1, F2, F8, F10 or DEL key. Make sure you save the settings before exiting)) If you are unsure or don't want to enter the BIOS then just test the computer by putting the CD-ROM in the drive and reboot your computer. This is the recommended way to install windows.
To begin insert your Windows XP Professional CD and reboot you computer. A message "Press any key to boot from CD....." will appear, press the space bar to continue.
Setup will now inspect your computer hardware and configuration. Setup now prepares your computer for install. From this menu press "ENTER" (NOT "R") to begin the repair install. Windows XP License agreement, read, and if you agree press "F8" to continue, press "ESC" if you disagree. If you disagree setup will finish.
Now select the operating system you wish to repair, if as in most occasions there is only one, the just press "R" to continue. Setup will now make some checks on the system.
and then prepare files that are needed to be copied.
Setup will now initialize your XP configuration.
Setup now needs to reboot your computer. Press "ENTER" to save yourself a 15 second wait.
Boot will recognize that the XP CD is in the drive, DO NOT press any keys, let setup bypass the CD boot.
Windows will now begin to load. On some occasions Windows will be finished the repair, if so it will go straight to Part 7. Which is the part where you arrive at the desktop, otherwise the install will continue.
The repair process continues. Windows will continue installing.
Windows setup will now finalize. It is now time to restart Windows XP again, press "ENTER" to speed up process, otherwise Windows will do it itself in 15 seconds. Boot will recognize that the XP CD is in the drive, DO NOT press any keys, let setup bypass the CD boot. Windows will continue loading.
Windows will now adjust your resolution, click "OK" to continue. If you are happy with the changes, click "OK" otherwise press "Cancel" to return to the old settings Windows will now apply changes. Be patient. Windows "WELCOME" screen. and finally the Windows XP Desktop. Windows is now repaired. Hopefully you will now be able to access and fix the problem that caused you to repair. Make sure you run a virus check, spyware check, and registry scan, also update to latest service pack, this may prevent the problem happening again.
|